Ashcroft GC30 Ultra-Compact Differential Pressure Sensor Instrukcja Użytkownika Pobierz pdf (Strona 13)





"#"#!!$"#"

hen the et( is selected in “Display Selection”, the display value of Pressure for applied

displays as an arbitrary scaling display. This is a function to scale the MIN/MAX display value

nd has NO effect on applied pressure and analog output.

$"#"

se the MODE key to set “Decimal point position”, “Minimum pressure range display value”

and Maximum pressure range display value” of “Display scaling”.

xample: With a pressure range of 0 to 25inWC (0 to 100% FS), main unit display of 00.0 to

25.0 (factory set) is changed to a display of 0.000 to 1.000.

d-p Dec. point position (from least significant digit): 0.1 Ÿ .003

d-l Min. pressure range value: 0.0 Ÿ .000

d-k Max. pressure range value: 25.0Ÿ 1.000

#!"#

The GC30 is equipped with 5 internal time constant filters. Use this function when pressure

fluctuations can result in erratic, difficult to read displays. The time constant for the selected fil

ters reflects on the switch outputs as well as the analog output.

Select “Filter Selection” with the MODE key. The message f;l is displayed for 1 sec. and

then the current setting mode’s decimal point position is displayed. Change the decimal point

position value with the  keys.

Entering the setting value in function setting mode resets all of the setting

f-0 No filter

f-1 Time constant 25ms

f-2 Time constant 250ms

f-3 Time constant 2.5 sec

f-4 Time constant 5 sec

f-5 Time constant 10 sec

$# $#"

This mode is for setting the pressure for the analog output zero point and span point. Display

by analog selection is scaled as 0 to 100% (Zero point: 1Vdc, Span: 5Vdc). Select “Analog

Scaling” with the MODE key.

The message a-l is displayed for 1 sec. and the current pressure’s analog output zero

point (1Vdc) is displayed as a percentage. Change the numeric value with the  keys.

The message a-k is displayed for 1 sec. and the analog output span point’s pressure can

be set in the same way using the  keys.

@)584- With Analog output of 1 to 5Vdc at pressure range of 0 to 10.0in WC (0 to 100%

FS), output is changed to 1 to 5Vdc at 0 to 9.0inWC.

Set the analog output zero point: 0.0% FS0.0% FS (1Vdc output with pressure range 0% FS).

Set the analog output span point: 100.0% FS90% FS (5Vdc output with pressure range 90% FS).

"&#"##"

"-<=8"<-8;

In Measurement Mode press the key (release within 3 sec.) to change to Switch Setting

Mode.

"?1<+0"-<<16/7,-

There are two switches, OUT1 and OUT2. Both “Hysteresis (upper/lower limit)” and “Window

Comparator” operations can be selected in the function setting mode (switch operation selec-

tion). Those two operations can be selected at once, and can be set. Both OUT1 and OUT2

can be set independently to a max on/off delay of 2 seconds. In the following explanation -

If the switch’s output conditions are met their output state will become On, and “Switch LED

(OUT1, OUT2)” will light up.

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 19 20

Komentarze do niniejszej Instrukcji

Brak uwag

Ashcroft GC30 Ultra-Compact Differential Pressure Sensor Instrukcja Użytkownika Strona 13

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Urządzenia pomiarowe Ashcroft GC30 Ultra-Compact Differential Pressure Sensor